LED球泡灯的烟囱效应散热设计与实验

唐帆; 郭震宁; 林介本; 廖炫; 潘诗发

doi:10.3788/fgxb20163705.0624

您当前的位置：

首页 >

文章列表页 >

LED球泡灯的烟囱效应散热设计与实验

发光学应用及交叉前沿 | 更新时间：2020-08-12

- LED球泡灯的烟囱效应散热设计与实验
- Thermal Design and Experiment of LED Bulb Using Chimney Effect
- 发光学报 2016年37卷第5期页码：624-630
- 作者机构：
  
  1. 华侨大学信息科学与工程学院福建省光传输与变换重点实验室,福建厦门,361021
  2. 福建泉州世光智能照明技术研究院有限公司,福建泉州,362302
- 作者简介：
- 基金信息：
  
  福建省科技计划引导性重点项目(2016H0022)();泉州市科技计划(2015TZ31)();华侨大学研究生科研创新能力培育计划(1400201001)资助项目()
- DOI：10.3788/fgxb20163705.0624
  中图分类号： TN312
- 纸质出版日期：2016-5-5，
  
  收稿日期：2016-2-18，
  
  修回日期：2016-3-16，
扫描看全文
唐帆, 郭震宁, 林介本等. LED球泡灯的烟囱效应散热设计与实验[J]. 发光学报, 2016,37(5): 624-630

TANG Fan, GUO Zhen-ning, LIN Jie-ben etc. Thermal Design and Experiment of LED Bulb Using Chimney Effect[J]. Chinese Journal of Luminescence, 2016,37(5): 624-630
唐帆, 郭震宁, 林介本等. LED球泡灯的烟囱效应散热设计与实验[J]. 发光学报, 2016,37(5): 624-630 DOI： 10.3788/fgxb20163705.0624.

TANG Fan, GUO Zhen-ning, LIN Jie-ben etc. Thermal Design and Experiment of LED Bulb Using Chimney Effect[J]. Chinese Journal of Luminescence, 2016,37(5): 624-630 DOI： 10.3788/fgxb20163705.0624.

摘要

为了增强LED灯具的散热能力

根据烟囱效应原理

设计了一种LED球泡灯

其具有特殊的直筒式烟囱结构。利用Solidworks建立三维模型

通过其插件Flow Simulation进行热仿真

并以烟囱高度30 mm、烟囱数量6、通风口长度2 mm的参数为基础模型。通过实验验证

测出该模型的最高温度为69℃

与仿真所得出的结果仅相差1.66℃

证实了仿真步骤的正确性。以此为基础

对不同烟囱高度和数量、通风口大小对LED芯片最高温度的影响进行研究。研究表明:烟囱效应明显增强了灯具的对流散热性能。在烟囱高度为45 mm、烟囱数量为12、通风口长度为3.5 mm时

LED芯片的最高温度为61.04℃

比优化前下降了9.62℃。在模型参数相同的条件下

最高温度比不加烟囱结构的LED球泡灯下降了1.9℃

且散热器重量下降了2.55 g。在自然对流条件下

所设计的LED球泡灯能很好地满足LED芯片工作要求。

Abstract

In order to enhance the cooling capacity of LED lamps and lanterns

we design a special LED bulb with straight chimney structure based on the principle of the chimney effect. We build a three-dimensional model by adopting Solidworks

and use its plug called Flow Simulation to simulate based on the model with the chimney height of 30 mm

chimney number of 6

and vent length of 2 mm. Through experiments

we find the highest temperature of this model is 69℃

lower than the simulation result only 1.66℃. It confirms the correctness of the simulation steps. Then

we study the influences of different chimney height

chimney number

and vent length on the highest temperature of LED bulb

respectively. The results show that the chimney effect can effectively improve the convection cooling performance of the LED bulb. When the chimney height is 45 mm

chimney number is 12

and vent length is 3.5 mm

the highest temperature of the LED chip is 61.04℃

which is 9.62℃ lower compared to the original model. Under the same set of model parameters

the highest temperature of the LED bulb has been reduced by 6.16℃ compared to the one in the model without a chimney structure

and the weight of radiator has also reduced 2.55 g. In conclusion

the designed LED bulb can better satisfy the working requirements under the nature convection conditions.

关键词

直筒式LED球泡灯烟囱效应最高温度

Keywords

straight typeLED bulbchimney effecthighest temperature

references

LIN Y C, TRAN N, ZHOU Y, et al.. Materials challenges and solutions for the packaging of high power LEDs[C]. Proceedings of International Microsystems, Packaging, Assembly Conference Taiwan, Taipei, China, 2006:1-4.

ARIK M, PETROSKI J, WEAVER S. Thermal challenges in the future generation solid state lighting applications:light emitting diodes[C]. Proceedings of The 8th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, San Diego, USA, 2002:113-120.

李菊华. LED灯具热设计与仿真[D]. 杭州:杭州电子科技大学, 2011. LI J H. Thermal Design and Simulation of LED Lamps[D]. Hangzhou:Hangzhou Dianzi University, 2011. (in Chinese)

王芳,张治民,吕猛,等. LED泡沫金属散热器的散热性能研究[J]. 铸造技术, 2014, 35(1):35-37. WANG F, ZHANG Z M, LV M, et al.. Heat dissipation performance of foam metal radiator used in LED[J]. Foundry Technol., 2014, 35(1):35-37. (in Chinese)

梁融,聂宇宏,聂德云,等. LED散热器散热特性分析及结构优化[J]. 照明工程学报, 2014, 25(1):94-97. LIANG R, NIE Y H, NIE D Y, et al.. Thermal analysis and structure optimization of LED radiator[J]. China Illuminat. Eng. J., 2014, 25(1):94-97. (in Chinese)

朱鹏. 基于烟囱效应对大功率LED灯的强化散热[D]. 大连:大连理工大学, 2014:20-24. ZHU P. The Enhancement of Heat Dissipation of High Power LED Lamp with Chimney Effect[D]. Dalian:Dalian University of Technology, 2014:20-24. (in Chinese)

陈柏仁,马小康,蓝浩玮,等. 蜂巢式散热鳍片应用于高功率LED散热的研究[J]. 太原理工大学学报, 2010, 41(5):554-563. CHEN B R, MA X K, LAN H W, et al.. Study of an LED device with a honeycomb heat sink[J]. J. Taiyuan Univ. Technol., 2010, 41(5):554-563. (in English)

陈启勇,何川,高园园. 大功率LED路灯散热器自然对流的数值研究[J]. 半导体光电, 2011, 32(4):498-501. CHEN Q Y, HE C, GAO Y Y. Numerical study on natural convection of high-power LED street lamp heat sink[J]. Semicond. Optoelectron., 2011, 32(4):498-501. (in Chinese)

李鸥. 工业厂区散热器的合理评价和选用[J]. 大科技, 2015(10):248. LI O. Reasonable evaluation and seledction of radiator for industrial plant[J]. Super Sci., 2015(10):248. (in Chinese)

张国旺,韩彦军,罗毅,等. 基于烟囱效应的集成封装半导体照明光源散热结构优化设计[J]. 半导体光电, 2013, 34(5):732-737. ZHANG G W, HAN Y J, LUO Y, et al.. Optimization of heat sink design based on chimney effect for integrated packaging semiconductor lighting source[J]. Semicond. Optoelectron., 2013, 34(5):732-737. (in Chinese)

李静,姬升涛,刘建勇,等. 电子元件散热装置的烟囱效应分析[J]. 电子与封装, 2011, 11(6):36-40. LI J, JI S T, LIU J Y, et al.. Analysis on the stack effect of cooling device of electronic components[J]. Electron. Packag., 2011, 11(6):36-40. (in Chinese)

李本红,刘海林. 烟囱效应在大功率LED灯具散热器设计中的影响分析[J]. 电子器件, 2014, 37(2):221-224. LI B H, LIU H L. Analysis of the chimney effect in thermal design of high-power LED lamps radiator[J]. Chin. J. Electron Dev., 2014, 37(2):221-224. (in Chinese)

何凡,陈清华,刘娟芳,等. 集成芯片LED场地照明灯新型叠片散热器热分析[J]. 发光学报, 2014, 35(6):742-747. HE F, CHEN Q H, LIU J F, et al.. Thermal analysis of high mast integrated LED lamp with new heatsink structure of laminated pure aluminum plate[J]. Chin. J. Lumin., 2014, 35(6):742-747. (in Chinese)

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

LED异形灯的散热设计与实验