浏览全部资源
扫码关注微信
1. 上海应用技术学院 理学院 上海,201418
2. 上海应用技术学院 材料与工程学院 上海,201418
3. 浙江亿米光电科技有限公司,浙江 嘉兴,314100
4. 上海博恩世通光电股份有限公司 上海,201108
纸质出版日期:2015-6-3,
收稿日期:2015-1-20,
修回日期:2015-4-9,
扫 描 看 全 文
邹军, 李杨, 朱伟等. 立体发光LED灯片的光学性能研究[J]. 发光学报, 2015,36(6): 657-660
ZOU Jun, LI Yang, ZHU Wei etc. Optical Characterization of Three-dimensional Light-emitting LED[J]. Chinese Journal of Luminescence, 2015,36(6): 657-660
邹军, 李杨, 朱伟等. 立体发光LED灯片的光学性能研究[J]. 发光学报, 2015,36(6): 657-660 DOI: 10.3788/fgxb20153606.0657.
ZOU Jun, LI Yang, ZHU Wei etc. Optical Characterization of Three-dimensional Light-emitting LED[J]. Chinese Journal of Luminescence, 2015,36(6): 657-660 DOI: 10.3788/fgxb20153606.0657.
立体发光灯片的关键是在保证光通量的前提下
如何获得均匀的正反面发光。本文对3种荧光粉平面涂覆立体灯片的正面和反面的瞬态和稳态光通量、色温、色品坐标进行了研究
发现直接涂覆荧光粉胶的灯片总的光通量最大
但正反面的发光性能相差很大;在涂覆荧光粉之前先平面涂覆一层硅胶
可获得正反面发光较均匀的灯片;而在该硅胶层内掺杂扩散粉的灯片
不但没有提高灯片的正反面发光均匀度
反而大幅度降低了光通量值。此外
测试3种样品的发光角度
发现其发光角度分布相似
而发光强度与积分球测试的光通量比值相近。结果表明
涂覆荧光粉之前先平面涂覆一层硅胶工艺
既可以保证立体发光灯片具有较大的光通量又可以获得均匀的正反面发光。
The luminescence performance characterized by luminous flux
color temperature
chromaticity coordinate of three-dimensional light emitting diodes (LEDs) has been investigated by using different phosphor coating methods. The LED die was directly coating with mixed phosphors and silicone which have the maximum total luminous flux. However
this encapsulation incurs luminous uneven problem of front and back which limit three-dimensional luminescence application. Therefore
this work attempts to use the silicon and spreading powder to change the light path on the basis of less loss of luminous flux. Experimental results indicate that the brightness uniformity can be improved when increasing silicon layer between LED die and phosphor
while spreading powder layer would induce significant light attenuation. Moreover
the three packing have similar light angle. Therefore
silicon layer provides an alternative packing solution for three-dimensional LED light application.
立体发光LED灯片光通量色温色品坐标
three-dimensional light-emittingLED lampluminous fluxcolor temperaturechromaticity coordinate
Chang M H, Das D, Varde P V, et al. Light emitting diodes reliability review [J]. Microelectron. Reliab., 2012, 52(5):762-782.
Wang C P, Chen T T, Fu H K, et al. Analysis of thermal characteristics and mechanism of degradation of flip-chip high power LEDs [J]. Microelectron. Reliab., 2014, 52(4):698-703.
Zhong G M, Du X Q, Tian J. Simulation and analysis of light extraction efficiency of GaN-based flip-chip light-emitting diodes [J]. Chin. J. Lumin.(发光学报), 2011, 32(8):773-778 (in Chinese).
Kim H, Lee S N, Cho J. Electrical and optical characterization of GaN-based light-emitting diodes fabricated with top-emission and flip-chip structures [J]. Mater. Sci. Semicond. Proc., 2010, 13(3):180-184.
Liu Y, Leung Stanley Y Y, Zhao J, et al. Thermal and mechanical effects of voids within flip chip soldering in LED packages [J]. Microelectron. Reliab., 2014, 54(9-10):2028-2033.
Li L, Fang Y Z, Zou J, et al. Non-polar ZnO thin films and LED devices [J]. Adv. Mater. Res., 2014, 1053:373-380.
Li Y, Dong S S, Wang Y R, et al. Optical characterization of light-emitting diodes fabricated with vertical and flip-chip structure [J]. Electro-Opt. Technol. Appl.(光电技术应用), 2014, 29(5):47-51 (in Chinese).
Qian K Y, Zheng D S, Luo Y. Thermal dispersion of GaN-based power LEDs [J]. Semicond. Optoelectron.(半导体光电), 2006, 27(3):236-239 (in Chinese).
Ma X J, Wu L G, Dai S X, et al. Thermal analysis of high-power LED downlight [J]. China Illumin. Eng. J.(照明工程学报), 2011, 22(6):18-21 (in Chinese).
Li A Y, Zhu W Z. Key factors in cooling of high-power LED packages [J]. J. Xiamen Univ. Technol.(厦门理工学院学报), 2011, 19(4):10-13 (in Chinese).
Wang Y R, Li Y F, Zou J, et al. White LED accelerated aging performance analysis [J]. China Light & Lighting (中国照明电器), 2014(10):43-46 (in Chinese).
Zhang S D, Wang F C, Zou J. Influence research on LED encapsulation light source from YAG phosphor with different particle size [J]. Electro-Opt. Technol. Appl.(光电技术应用), 2014, 29(4):21-23 (in Chinese).
0
浏览量
47
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构