The Impact of Different DPVBi Thickness and Position on the Organic Light-emitting Devices

您当前的位置：

首页 >

文章列表页 >

The Impact of Different DPVBi Thickness and Position on the Organic Light-emitting Devices

更新时间：2020-08-11

- The Impact of Different DPVBi Thickness and Position on the Organic Light-emitting Devices
- Chinese Journal of Luminescence Vol. 28, Issue 2, Pages: 189-192(2007)
- 作者机构：
  
  1. 吉林师范大学信息技术学院,吉林四平,136000
  2. 吉林师范大学继续教育学院,吉林四平,136000
- 作者简介：
- 基金信息：
- DOI：
  CLC： TN381.1;TN873.3
- Received：13 June 2006，
  
  Revised：10 November 2006，
  
  Published：20 March 2007
- 稿件说明：
移动端阅览
王广德, 王立, 姜文龙, 王立忠, 汪津, 韩强, 丁桂英. DPVBi的厚度和发光位置不同对有机电致发光器件性能的影响[J]. 发光学报, 2007,28(2): 189-192

WANG Guang-de, WANG Li, JIANG Wen-long, WANG Li-zhong, WANG Jin, HAN Qiang, DING Gui-ying. The Impact of Different DPVBi Thickness and Position on the Organic Light-emitting Devices[J]. Chinese Journal of Luminescence, 2007,28(2): 189-192
王广德, 王立, 姜文龙, 王立忠, 汪津, 韩强, 丁桂英. DPVBi的厚度和发光位置不同对有机电致发光器件性能的影响[J]. 发光学报, 2007,28(2): 189-192 DOI：

WANG Guang-de, WANG Li, JIANG Wen-long, WANG Li-zhong, WANG Jin, HAN Qiang, DING Gui-ying. The Impact of Different DPVBi Thickness and Position on the Organic Light-emitting Devices[J]. Chinese Journal of Luminescence, 2007,28(2): 189-192 DOI：

摘要

通过调整发光层DPVBi的厚度和在器件中的位置

在同一实验条件下设计了不同的器件结构

制备了有机电致发光器件

在实验中可看到DPVBi的厚度不同

器件的色度发生了改变

并且发现DPVBi在器件的不同位置

器件的发光特性也是不同的。通过实验可以得知处于器件不同位置的DPVBi

其发光机理是不同的

这是由于DPVBi和Alq

3

的最高未占有轨道(HOMO)能级相差不多

而它们的最低占有轨道(LUMO)能级相差0.4eV

这样DPVBi的存在有利于电子的注入

同时由于rubrene和DPVBi的HOMO相差0.5eV

这样空穴和电子就在rubrene和DPVBi的界面处形成激子复合而发光。也就是说

在rubrene之后的DPVBi对空穴有了阻挡作用

使器件中的空穴和电子达到平衡。通过改变DPVBi的厚度

制备了白光器件

这组白光器件

在7～17V变化范围内器件的色坐标从(0.35

0.37)到(0.33

0.35)变化不大

接近白光等能点(0.33

0.33)

是色度比较好的器件。

Abstract

By adjusting thickness and luminous place of the luminous DPVBi layer in the same laboratory conditions

organic light-emitting devices have been produced. We designed different device structures and have produced a luminous device in the experiment. Firstly

we designed a group of devices with same structures perfectly

except different DPVBi layer thickness

as a result

their spectrum changed. When DPVBi layer thickness was 5 nm yellow-light was emitted.When DPVBi layer thickness was 10nm white-light was emitted because blue and yellow light were emitted symmetrically. With increase gradually of DPVBi layer thickness

ingredient of bluelight was increasing

and the emission color of the devices transferred little by little into blue. As a result

the emission hue of device changed due to different thickness of DPVBi layer. Secondly

DPVBi layer was laid on the different places in the device

the luminous performance of the device was different. From the experiment we can see that the DPVBi layer in different place had the different luminous essences: the luminous DPVBi layer before rubrene emitted blue light as a light-emitting layer;but the luminous DPVBi layer after rubrene didn't emitted light. According to compare of HOMO and LUMO energy grade used in the materials

the luminous DPVBi layer after rubrene performed an function of hole block only. This would affect the luminous brightness and efficiency of the organic light-emitting devices to a large extent. If by adjusting reasonably thickness and luminous place of the luminous DPVBi layer

the light hue of devices may be adjusted to gain colors expected. On the other hand

white-light devices were expected to produce

which was significant.

关键词

Keywords

references

0

Views

139

下载量

6

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Related Articles

Effect of YF₃ Electron Injection Layer on The Performance of Organic Light-emitting Devices

Effect of Contaminated Organic/Organic Interface on The Stability of Organic Light-emitting Devices

High Efficiency Phosphorescent Organic Light-emitting Devices Based on Multiple Quantum Well Structure

Synthesis and Luminescence Property of Two New Blue Phosphorescent Iridium(Ⅲ) Diazine Complexes

Improved Performance of Organic Light Emitting Diodes Using Combined Hole-injecting Layer

Related Author

LIU Xing-yuan

LIN Jie

ZHENG Xuan-ming

ZHANG Lei

WU Zhao-xin

ZHANG Xin-wen

ZHAO Bo

LI Wen-lian

Related Institution

State Key Laboratory of Luminescence and Applications, Changchun Insitute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences

University of Chinese Academy of Sciences, Beijing 100049, China

南京邮电大学有机电子与信息显示国家重点实验室培育基地

西安交通大学电子与信息工程学院信息光子技术省重点实验室

State Key Laboratory of Luminescence and Applications, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China Postal code：130033
Tel：0431-86176862 Email：fgxbt@126.com
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰